Changes
Jump to navigation
Jump to search
Note: Most of the coding in this section is out of date, and refers to the .shader version, not the current .cg version.
float4 weights = float4(distance / 0.3);
===Sharpness===
[[File:Retroarch_2013-07-22_19-24-11-41.png|thumb|225px|CRT-Geom-Flat, at 2x sharpness]]If you find the shader looks too blurry, you can increase the sharpness by going to the sections in the code that have the following lines (should be at the beginning of both the vertex and fragment portions of the shader code):
uniform vec2 rubyInputSize;
uniform vec2 rubyTextureSize;
then add these lines afterwards:
vec2 InputSize = vec2(n*rubyInputSize.x, rubyInputSize.y);
vec2 TextureSize = vec2(n*rubyTextureSize.x, rubyTextureSize.y);
[[File:Retroarch_2013-07-22_19-27-22-65.png|thumb|225px|CRT-Geom-Flat, at 4x sharpness]]Replace "n" with either 2 for increased sharpness, or 4 for maximum sharpness. Then Ctrl+F and seek out any portions of the code that say "rubyInputSize" and "rubyTextureSize", and replace them with "InputSize" and "TextureSize" respectively.
To obtain thinner, 480p-esque scanlines, first tweak the shader to apply greater sharpness, but only apply it to the TextureSize. The code should look like this: uniform vec2 rubyTextureSize; vec2 TextureSize = vec2(2*rubyTextureSize.x, 2*rubyTextureSize.y);[[File:Retroarch_2013-07-22_19-31-23-11.png|thumb|225px|CRT-Geom-Flat, with thin scanlines]]Again, this is for both the vertex and fragment portions. Don't forget to seek out any other instances of rubyTextureSize, and replace them with simply TextureSize. Now, go to the beginning of the fragment portion, and modify it as such: <fragment filter="nearest" outscale_x="1" outscale_y="2"><![CDATA[This will only yield satisfactory results at 4x integer scale. Anything else will likely cause problems. It might also be wise to disable the phosphor emulation, as leaving it on produces a "grid"-like effect, which may or may not be desirable.?
To make it flat, just set cornersize (line 107) to something small, like 0.001 and cornersmooth (line 110) to something large, like 8000.0. Then, comment out (i.e., put two slashes in front of it, like this: // ) line 141, #define CURVATURE.
//#Define Curvature
//#define INTERLACED
//#define DOTMASK
If you find the effect too strong on the Halation version, go to the following line of code:
mul_res += pow(tex2D(decal, xy2).rgb, float3(monitorgamma))*0.1;
Lowering the last number reduces the effect of the halation. This is prefered since the default halation level is too high.?
→Tweaking CRT Geom
==Tweaking CRT Geom==
CRT Geom is highly customizable. You can open up CRT Geom in [http://notepad-plus-plus.org/ notepad++] and edit it. Regular notepad will work, but notepad++ is recommended.
===Scanline Brightness===
Raise the 0.3 to a higher value to make the scanlines brighter. I do not recommend going past 0.4, as at that point on bright colors scanlines completely disappear, and going further makes them appear again, but on the wrong field in said bright colors, which is inaccurate. Try 0.35.
===Scanline Size===
===Curvature===
Define Curvature. Something like that Comment it out. That means adding "//" in front of it. It should look like this when you're done:
===Interlacing===
For the original, to disable interlacing, comment it out:
===Phosphor===
[[File:Retroarch_2013-07-22_19-33-30-35.png|thumb|225px|CRT-Geom-Flat, with phosphor disabled]]To disable phosphor emulation (which alternately tints pixels green and magenta), comment out #define DOTMASK:
===Halation===
[[Category:FAQs]]
[[Category:Shaders/Filters]]
