Changes
Jump to navigation
Jump to search
Mednafen is very picky about which BIOS to use. The ones that you might need are:
<ul>
<li class="de2"><code>scph5500.bin</code></li>
<li class="de2"><code>scph5501.bin</code></li>
<li class="de2"><code>scph5502.bin</code></li>
</ul>
[[Mednafen]] RetroArch requires you to load games through CUE sheets. Ensure that the CUE sheet is properly set up in order for the game to run. See the [[Cue sheet (.cue)]] for more.
Mednafen RetroArch creates memory card files for each individual game, in contrast to PCSX-R/ePSXe where all game saves are stored into 2 memory card files. To transfer memory card files from PCSX-R/ePSXe to RetroArch:
→Hotkeys
==Basic Usage==
{{Main|Dummies Guide: RetroArch}}
After downloading [[RetroArch]],[[File:Rgui.png|thumb|205px300px|RGUI, RetroArch's original interface. ]][[File:GLUI.png|thumb|300px|GLUI]][[File:XMB and GLUI follow the same basic structure.jpeg|thumb|300px|XMB]][[File:Ozon.png|thumb|300px|Ozon]] start up retroarch.exe.
To launch a game, select the libretro core you'd like to use under '''Load Core''', and select a ROM under '''Load Content>Select File'''. Alternatively, you can use '''Load Content>Select File And Detect Core''' to be presented with a list of cores detected based on the file extension of the content.
sudo apt-get update
sudo apt-get install retroarch retroarch-assets retroarch-joypad-autoconfig
sudo apt-get install <corename>
Set USE flags that you want, it is not required to enable every single one (you only need at least one audio and video output device; defaults are suitable enough). It is recommended to add udev for joystick support and netplay for netplay support.
Build and install RetroArch from the git repository
The cores will be installed under /usr/lib/libretro/
===Other Distros===
If you are going to play in a system that needs a BIOS (e.g. PS1), place the [[Emulator_Files#Multi-System|BIOS files]] in RetroArch's 'system' directory.
===Disc images===
===Mupen64Plus===
*Angrylion is ultra accurate, but is too slow for most people to use. Requires the CXD4 RSP to work. Resolution must be set to 640x480 or higher.
*ParaLLEl paraLLEl is a Vulkan renderer based on Angrylion. It is much faster than Angrylion, but is still incomplete and has more issues. Turning Synchronous RDP off results in a speed boost, but also breaks many things.
*The HLE RSP plugin is very fast and will work fine for most games.
===Transfer PS1 Memory Card Files===
*Start game in RetroArch.
===SoftFilters===
Classic emulator filters like SuperEagle or Blargg's NTSC have been available as bSNES bsnes filter plugins in the past, which is no longer supported in bSNESbsnes/higan but was still available in RetroArch. However, this filter format was recently replaced with the SoftFilter spec, which has been upgraded to support more platforms, multi-threading and SIMD usage. The filters are dynamic libraries which are loaded in the menu under Settings>Video>Video Filter, which will apply the filter before any shaders are applied.
The filters are found [https://github.com/libretro/RetroArch/tree/master/gfx/video_filters here], which can be built for your platform with the makefile. These files should be included in nightly builds from the buildbot.
Note that these filters are WIP and may not work with all cores as they need to have codepaths for the pixel format the core uses (either 32bpp XRGB8888 or 16bpp RGB565). Blargg's NTSC is currently limited to 16bpp cores for example (bSNES bsnes is 32bpp so it won't work, but SNES9x Snes9x is 16bpp so it works there). Cores that use Libretro GL for 3D like Mupen64plus Mupen64Plus can not use these filters.
===Outputting log to a file===
*F1 - Open menu
*F2 - Save state
*F3 - Toggle frame rate display
*F4 - Load state
*F6 - Input save state slot decrease
